A large part of the cause of the bearing is not the right installation method. Different types of bearing installation methods are different. The small axis brings together various bearing installation methods today for your reference.

 

Various bearing installation instructions

 

Instructions for rolling bearings

 

1. When installing bearings, it should be uniform and cannot be hammered directly. If the conjunction of a large profile is large, the bearing should be placed in the air heating furnace or oil furnace of the automatic temperature control, and the heating temperature should be strictly controlled below 120 ° C.

 

2. The bearings with nylon holding frames can continue to work continuously for a long time under -40 ° C ~ 120 ° C. At 150 ° C, it should not work for more than 4 hours, and the short-term temperature peak can reach 180 ° C.

 

3. The warehouse of the bearing should be cleaned. The drying should not be stored in the same warehouse as the chemical products. The relative humidity should not exceed 65%, and the bearings are not allowed to be stored.

 

Deep ditch bearing installation and use

 

1. When installing bearings, it should be uniform and cannot be hammered directly. If the conjunction of a large profile is large, the bearing should be placed in the air heating furnace or oil furnace of the automatic temperature control, and the heating temperature should be strictly controlled below 120 ° C.

 

2. The bearings with nylon holding frames can continue to work continuously for a long time under -40 ° C ~ 120 ° C. At 150 ° C, it should not work for more than 4 hours, and the short-term temperature peak should not exceed 180 ° C.

 

3. The warehouse of the bearing should be cleaned. The drying should not be stored in the same warehouse as the chemical products. The relative humidity should not exceed 65%, and the bearings are not allowed to be stored.

 

4. Inventory bearings should be cleaned again every other year for rust -proof packaging.

 

Corner contact ball bearings installation and use

 

1. When installing bearings, it should be uniform and cannot be hammered directly. If the conjunction of a large reap, the bearings should be heated in the air heating furnace or oil furnace of the automatic temperature control, and the heating temperature should be strictly controlled below 100 ° C.

 

2. The bearings with nylon holding frames can continue to work continuously for a long time under -40 ° C ~ 120 ° C. At 150 ° C, it should not work for more than 4 hours, and the short-term temperature peak can reach 180 ° C.

 

3. The warehouse of the bearing should be cleaned. The drying should not be stored in the same warehouse as the chemical products. The relative humidity should not exceed 65%, and the bearings are not allowed to be stored.

 

Installation and use of roller bearing

 

1. The user should choose the appropriate cooperation and the radial gap of the bearings according to the requirements of the use. After the package is disassembled, please school the bearing node first.

 

2. Before the bearing installation, if you need to refuel grease in the bearings, the oil must be cleaned and appropriate.

 

3. During installation, it is advisable to hit the inner face and roller without direct hammer, so as not to crack the inner ring or middle and small gears. Usually users should put the bearing in the mineral oil to heated to 90 ° C ~ 100 ° C and immediately install the main shaft. Do not use a local spray method for bearing. When it is difficult to "heat", users should also use a special sleeve to install.

 

4. There should be a good sealing dustproof device and lubrication in the use of bearing to break the oil.

 

5. The bearing warehouse should be cleaned and dry, no environmental pollution, the bearing stack does not land, and the packaging is not broken. The bearing with an inventory of more than one year must be re -washed and applied.

 

Plustering Rolling Rolling Bearing Installation and use

 

1. When installing the bearings, wash the bearings oil, and then apply clean high -quality lubricant.

 

2. When installing bearings, it should be uniform and cannot hammer. If the conjunction of a large impact, put the bearings into the mineral oil and heat it to 90 ° C ~ 100 ° C, and install it immediately.

 

3. The warehouse of the bearing should be cleaned, clean, and the relative humidity should not exceed 65%.

 

4. Inventory bearings should be cleaned and applied again every other year, and the oil seal packaging is maintained well.

 

5. When using bearing, there should be a good sealing dustproof device, and the work should be checked frequently.

 

Pillar roller bearing installation and use

 

1. The bearing is a separate type, and the user can adjust the gap by themselves when installing.

 

2. Before use, use gasoline or kerosene to clean and keep it well lubricated.

 

3. When installing the bearing, the bearings should be pressed into the component, and knocking is strictly prohibited.

 

4. The bearing store should be cleaned and ventilated to avoid humidity. The bearing that needs to be kept for a long time, and the rust should be proof regularly.

 

Plug -in ball bearings installation and use

 

1. When installing the bearings, the bearing should be removed, then washed and then applied to the clean high -quality lubricant.

 

2. When installing bearings, it should be uniform and cannot hammer. If the conjunction of a large impact, put the bearings into the mineral oil and heat it to 90 ° C ~ 100 ° C, and install it immediately.

 

3. The warehouse of the bearing should be cleaned, clean, and the relative humidity should not exceed 65%.

 

4. Inventory bearings should be cleaned and applied again every other year, and the oil seal packaging is maintained well.

 

5. When using bearing, there should be a good sealing dustproof device, and the work should be checked frequently.